|
|
|
|
|
Salient Features of Actimix Technology |
|
|
|
|
|
|
Classified Chemical Invention @ IENA Germany 2010 |
Designed for Performance in High Thermal Efficiency Manual Fired Boilers |
|
| Downloads |
Registers the best results in the Highest Thermal Efficiency Operating condition |
Results over & above GCV of the input fuel |
Downloads |
| Project Reports |
Temperature, Gas, Steam Profiles, remain unchanged. |
Effect on input Kcal only |
Boiler Optimization |
| Boiler Data Sheets |
Lesser Black Smoke, CO2 emissions |
Lesser Clinker formation |
Sales Initiatives |
| Lower LOI |
Lower Kcal / MT Steam |
| Technical Presentation |
Tests in PTC 4.1, Direct Method |
Comparison report on Kcal / MT Steam |
Safety Information |
| Steam Cost Reduction between 15 to 24% (Identical GCV fuel) |
|
Technical Support for maximizing Boiler Performance through Chargewave Energy-Pro Combustion Projection Software |
|
|
Results Proof in Storage Yards, Purchases, Balance Sheets within 3 to 6 months |
|
| Easy to Implement & Establish |
|
|
|
|
|
|
|
|
| Assured Advantages in Wide Span of Boiler Design |
|
| Actimix Chemicals are well established to lower Steam Generation Costs in all types of High / Medium / Low Thermal Efficiency Manual Coal & Biomass fired Boilers (Thermax / CVL / IBL / Veesons / Santhi / Thermal Systems / Cheema & many other Boiler Manufacturers) |
|
|
|
|
| Laces Extra Fire Power & Combustion Power to your fuel |
|
| Actimix Chemicals are specially designed Inorganic chemicals for lacing extra Fire Power & Combustion Power to all types of Coal & Biomasss, Coal, Lignite employed in High Thermal Efficiency operating Manual Fired boilers |
|
|
|
|
| Alters Thermal Energy Generation to create more impact |
|
| Actimix targets the floor conditions for proper CO2 reaction & raises the combustion reaction efficiency by 25 to 30% over the mechanically induced condition. Carbon & Oxygen thus vigorously react in the most efficient conditions releasing energy in uniform, highly concentrated, intensive heat cycles with 25% more fire & impacting power |
|
|
|
|
| Reaction Conditions Comparison-Table |
|
| Parameter |
Mechanically Induced Condition |
Chemically Induced Condition |
|
| Reaction Efficiency of CO2 |
65% to 75% |
95% to 99% |
|
| Thermal Energy & Intensity |
Scattered & Normal |
Concentrated & Very High |
|
| Heat Energy Cycles |
Variable band width |
Single band width |
|
| Thermal Power & Impact |
Normal |
+ 25% |
|
| Steam Profile |
As Operation |
As Operation (No Change) |
|
| Temperature Profile |
As Operation |
As Operation (No Change) |
|
| Boiler Thermal Efficiency % |
As Operation |
As Operation (No Change) |
|
| Input Kcal / MT Steam |
Normal |
15 to 20% Less |
|
| Steam Generation Cost / MT |
Normal |
15 to 20% Less |
|
|
|
|
|
| Dosage Information |
|
| Actimix dosing is upon raw Coal & Biomass in prescribed dosages by spraying by hand & then feed the Actimix added Coal & Biomass into the boiler |
| Dosage 1.2 to 1.5Kg / MT fuel |
|
|
|
|
|
| 3 Steps to Lowering Steam Cost |
| Step 1 : Make available Boiler Design & Operation Information |
| Step 2 : Nominate Management Representative, Local / Third Party Energy Auditors for data Acquisition & Certification |
| Step 3 : Conduct PTC 4.1 Direct method & Compare Kcal/MT Steam With & Without Actimix application |
|
|
|
|
| (Pre-requisites for PTC 4.1 Direct Method) |
| Performance / Application under Highest Thermal Efficiency, Boiler Operating Condition |
| Fuel MT, Sampling, GCV, Ash%, Moisture%, Ash MT reports (Under Identical Coal & Biomass Mix ratio) |
| Working Condition of Water / Steam Flow Meter, Boiler Instrumentation |
| Permission to Implement & comply suitable turbulence conditions for Actimix working |
|
|
|
|
| Results Declaration |
|
| Straight Comparison of Steam Generation Cost(Kcal Cost / MT Steam) |
|
|
|
|
|
